KO-SEAL II is a two component acrylic urethane primer sealer. KO-SEAL II has two series of products: one series meeting the VOC requirements for National Rule and one series meeting the VOC requirements for SCAQMD Rule 1151.
National Rule Compliant Products VOC= 4.58 lbs./gal 550 g/l KS-10 White Primer Sealer KS-11 Black Primer Sealer KS-12 Metallic Primer Sealer
SCAQMD Rule 1151 Compliant Products VOC= 2.08 lbs./gal 250 g/l KS-210 White Primer Sealer KS-211 Black Primer Sealer KS-212 Metallic Primer Sealer
NOTE: KO-SEAL II CAN NOT BE APPLIED OVER BARE METAL SURFACES OF ANY KIND. KO-SEAL II MUST BE APPLIED OVER SANDED AND CLEAN PRIMER OR PROPERLY PREPARED AND SANDED PREVIOUSLY PAINTED SURFACES FOR PROPER ADHESION.
NOTE: KO-SEAL II may be used as a base color for UK Kandy's. After KO-SEAL II has dried for one hour, topcoat with UK Kandy per UK Kandy tech sheet. KO-SEAL II may be tinted up to 5 by volume with any KK Kandy concentrate to achieve hundreds of different color combinations.
KO-SEAL II is a high quality sealer designed to:
KO-SEAL II can also be used as a fast drying and excellent sanding primer.
KO-SEAL II is a high quality acrylic urethane catalyzed primer sealer designed to be used with either our Kustom Kolor Acrylic Lacquer or Kosmic Kolor Urethane Enamel systems. KO-SEAL II is an excellent ground coat for base coat application. Choose the appropriate color for the base coat system and color that is going to be applied. KO-SEAL II black and white colors may be intermixed for various shades of gray. See KO-SEAL II Color Reference Chart for proper color selection.
Read "TECH PREP" thoroughly before you begin painting. Use only House of Kolor's KP Epoxy Primers over bare metal substrates or metal substrates with body work. Read and follow all label instructions. See tech sheet for more information of KP Epoxy Primers.
FOR KS-10, KS-11, and KS-12 Mix (by volume) 4 parts KO-SEAL II to 1 part KU-150 Exempt Catalyst, to 1 part Kosmic Reducer to remain at 4.58 VOC. Use a reducer best suited to your shop conditions. See tech sheet for more information on reducers. Mix well and strain into gun. For primer application, omit or add only 10 (0.5 part) reducer for higher film build. Pot life 1 hour.
FOR KS-210, KS-211 and KS-212 Mix (by volume) 4 parts KO-SEAL II to 1 part KU-150 Exempt Catalyst, to 1 part RU-300 VOC Exempt Reducer, to remain at 2.08 VOC. Substituting RU-310, RU-311 or RU-312 will give a 3.5 VOC product.
See tech sheet for more information on reducers. Mix well and strain into gun. For primer application, omit or add only 10 (0.5 part) reducer for higher film build. Pot life 1 hour.
Strain the paint into the paint gun. Air pressure 40-55 psi at the gun. 10 psi at the nozzle of HVLP. Gun distance while spraying should be approximately 6 to 8 inches. Apply 1 or 2 medium wet coats with 50 pattern overlap. Walk long objects. Be sure of thorough coverage. Allow flash time between coats. KO- SEAL II FLASH TEST - ALLOW TO FLASH DULL BETWEEN COATS. USUALLY 5 TO 10 MINUTES. If used as primer apply 2-3 coats.
Allow to dry 1 hour but no longer than 24 hours before top coat application. (Dry time may vary with weather and shop conditions.)
NOTE: If excessive dry time has elapsed, wet sand and reseal surface for positive adhesion of topcoats. If used as a primer, can sand in 2 hours. Weather and shop conditions can vary sand time.
NOTE: 400-500 grit (wet) or gray scuff pad may be used to remove dirt particles that occur during application.