TCP Global: automotive paint, restoration supplies, airbrushes, spray guns...

Holds car door open and firm for body shop work.

• Holds door open while you hammer, pull, grind, sand or paint.
• For doors and deck lids
• Holds solid
• Fits any size latch

The Hatch Jammer easily adjusts the work angle of the hatch door to a comfortable and secure position to repair and paint the outer skin of the hatch.

Easily holds hatches open and secure for prep, paint, buffing and paintless dent removal!

• Easily adjusts the work angle
• Improves visibility of the work area
• J-hook attaches securely to striker and larger loop end locks into latch.
• Saves up to 10 minutes of set-up time
• Reduces back stress

All the advantages of our regular Hatch Jammer, but with an extended reach of 59 inches! Also available, Xtension tube to convert your existing Hatch Jammer to an XL version.

Easily holds hatches open and secure for prep, paint, buffing and paintless dent removal!

• Easily adjusts the work angle
• Improves visibility of the work area
• J-hook attaches securely to striker and larger loop end locks into latch.
• Existing Hatch Jammer owners can buy the Xtension tube seperately to convert theirs to a Hatch Jammer XL
• Saves up to 10 minutes of set-up time
• Reduces back stress

Steck's classic pull rod set has been a staple tool for autobody repair and restorers for years.

• Super tough alloy steel is precisely heat-treated for maximum strength.
• Every Steck Pull Rod and Pick Pull is factory tested under a 500 pound (228 kg) load.
• Vinyl coated handle is comfortable to use.

The Steck HandyBar is a high-strength, non-marring bar useful for hammering out dents, inside quarter panels, rear body lines and more!

• Hammer out dents.
• Hammer inside quarter panels, rear body panels,
  body lines, etc.
• Use to block doors and hoods.

Allows the technician to quickly grip studs (pull pins) and controll the dent pulling process as well as the accuracy of the pull.

• Accurate controlled pulls every time
• Grips studs (pull pins) quickly & easily
• Standard tool works on both 2.2 and 2.6 mm studs as close as 3/8" apart
• Black pivoting base helps compress crown as dent is pulled
• Includes STECK Straight Edge #20003 for matching original contours

Steck Manufacturing Company has released another winning tool: The Stud Lever (P/N 20014) will allow a technician to quickly grip studs (pull pins) and controlling the dent pulling process as well as accuracy of the pull.

A strong reinforced Nylon lever with pivoting base and self-locking stud capture mechanism allows the technician to quickly lock and lever studs while also compressing the crown area of the dent with the pivoting base. Adjustable pivot base on the Stud Lever allows one-handed operation and provides increased leverage, accuracy and reach for the pull and crown compression processes both vertical and horizontal, including roofs and lower rocker panels.

Stud Lever’s unique stud capture mechanism allows technician to quickly and easily capture both 2.2mm and 2.6mm studs as close as 3/8 inches apart.

Included with the Stud Lever is the Steck Straight Edge, part number 20003, which allows the technician to align the stud pull with the non-damaged metal area for accurate pulls on the initial pull which minimizes metal work and reduces the need for slide hammers.

Labor/Material Savings: Quick attachment to stud while combining leverage, accuracy and compression of crown area with the initial pull reduces the metal work in the dent repair process by 15 minutes per hour.

Heavy-duty chisel that allows for easy separation of spot welded or bonded panels.

• Save up to 15 minutes per panel replacement.
• For quarter panels, rockers and any other pinchweld.
• Sharpened on two edges, the sharp end allows for penetration between panels and the side edge allows for side impact to drive the panels apart without damage.
• Super tough allow steel.
• Cushioned handle absorbs shock.

90 degree end to easily separate hard-to-reach spot welded or bonded panels.

• Save up to 15 minutes per panel replacement.
• For quarter panels, rockers and any other pinchweld.
• Sharpened on two edges, the sharp end allows for penetration between panels and the side edge allows for side impact to drive the panels apart without damage.
• Super tough allow steel.
• Cushioned handle absorbs shock.

90 degree end to easily separate hard-to-reach spot welded or bonded panels.

• Save up to 15 minutes per panel replacement.
• For quarter panels, rockers and any other pinchweld.
• Sharpened on two edges, the sharp end allows for penetration between panels and the side edge allows for side impact to drive the panels apart without damage.
• Super tough allow steel.
• Cushioned handle absorbs shock.

Quickly access hard to reach damaged frame flanges, door an hood edges, as well as radiator supports to bring back proper edge alignment.

A unique double ended revers 1/4 inch hook design, made from hardened alloy steels, gives the technician easy access to buckled metal edges. A flat hook allows for easy manual alignment while the 35 degree angle bar allows technician to access areas like radiator supports. Flange Lever design allows for mulitple angles to gain hand clearance for fland and/or angled pulls while using the body of the tool to provide maximum leverage for manipulating the damaged flange or edge panel.

Quick movement along the damaged area allows for multiple metal manipulations without needing to unlock and relock locking pliers used today to perform flange repairs.

The Panel Shaper is an air hammer driven set of three self lubricating Nylon reinforced heads that allow the technician to easily access deep reach areas and badly deformed sheet metal surfaces to form them back to original shapes. Each kit contains three unique Nylon head shapes with arbors that allow each tool to be attached to your air hammer to fix body lines, concaved areas and flat surfaces.

1. Chisel Head - works with door, body lines, corner shaping and fender edges.
2. Rounded Head - straightens out wheel house and quarter panels
3. Flat Head - straightens out floors, trunk floors and provide stress relief in the repair process.

Using the Panel Shaper’s with your air hammer gives needed vibration along the damaged frame areas providing stress relief and molecular realignment in the frame structure. Panel Shaper kit also allows you to form custom shape patch panels and to fabricated panels. Heads can also be customized by grinding the head to any specific angle and shape required to perform the repair. In the typical repair processes each head should last 10 work hours.

Labor/Material Savings: Saves the technician arm fatigue and up to two hours of repair time over traditional hammer repair.

Collision force to one front fender often travels through the hood to push out the top of the opposite fender. The Fender Fixer rolls that fender top back into shape in just minutes.

1. Hook strap below fender.
2. Place chisel point of tool into corner of bolt flange of fender. Adjust strap.
3. Lifting motion rolls fender into desired location. Hammer top of tool to set.

See the Fender Fixer video.

For pulling hard-to-clamp corners.

• Allows side pulls on corners of door openings, or in-line pulls with the optional linear pull ring.
• Also works in other hard-to-pull places for multi-directional pulls... and reverse pulls.

For pull pins and flanges. Pulls up to 2000 lbs.

• Grip and pull multiple pull pins studs and vertical or horizontal flanges.
• 3.5 inch jaw provides evenly distributed pulling force while pulling multiple pull pins or flanges.
• 2 large pulling rings for light pulling (up to 2,000 lbs.)

The ultimate tool for cleanly releasing molding.

• Slide tool left or right under the molding until it hooks a retaining clip
• Then just rock the tool with a twist of the wrist
• Heat-treated, high-carbon steel

Your all-in-one tool for trim work:

1. Molding Remover
2. Windshield Wiper Wrench
3. Clip/Wire Starter
4. Door Weather Strip Clip Remover
5. Trim Pad Remover
6. Door Handle Clip Remover
7. Headlight Spring Tool
8. Windshield Molding Clip Release
9. Door Clip Remover
10. Panel Seam Clean-up

New and improved version of our E-Z Strip molding tool with a 3-inch non-marring blade and steel air hammer arbor to remove body side moldings. Durable non-marring wedge design made from polypropylene rmoves moldings without damaging the molding or scratching paint surfaces. Kit also includes an additional wedge. Wedges can be trimmed to remove moldings imbedded in body lines.

• Saves body moldings
• Reduces body damage
• Saves time and materials
• Can be ground for special requirements

Fits most antenna bezel nuts, domestic and foreign.

• Fits most antenna bezel nuts -- domestic and foreign.
• Simple and compact. Compared to a socket set, it's easier to carry and use. It also costs much less!
• Rugged steel construction for many years of use.

Fits most antenna bezel nuts, domestic and foreign.

• Fits most antenna bezel nuts -- domestic and foreign.
• Simple and compact. Compared to a socket set, it's easier to carry and use. It also costs much less!
• Rugged steel construction for many years of use.

This non-marring wedge has a 1 inch blade with a curved clip end that allows easy access and removal of platic bezels, moldings, trm and panels without scratching the surface.

• Remove bezels, moldings, trim and panels easily.
• Non-marring, won't scratch paint.
• Great for removing weather stripping.

Have you ever tried removing a door hinge bushing with just a regular punch? You know it's a hassle. Now there's the Steck Bushing Tool. Its special design makes it easy to punch out bushings, and helps align bushings when reinstalling.

• Offset design allows for easy access to all door hinges.
• Easily punch out bushings.
• Breaks fewer bushings.
• Super tough alloy steel.

The ultimate solution for removing door pins FAST!

• Removes door hinge pins FAST
• Drives out even stubborn hinge pins
• Direct impact
• Clearance for door panels
• Works on all GM cars with removable hinge pins
• Includes PIN PULLER to remove loosened pins

Finally a Convenient Door Aligning Tool

• Saves space. Fits easily into your tool drawer. No long, heavy bar to store!
• Uses your breaker bar for leverage.
• Save time. You won't have to hunt for the shop tool.

The E-Z Rest Door Hanger enables a single person to quickly remove and/or install vehicle doors. The padded, removable side rails allow for accurate positioning of door, and the easy on/off design quickly adapts to most floof jacks with removable saddles. (floor jack not included)

• Reduces Labor Time
• Padded, Removable Side Rails
• Easy On/Off Design and Fully Adjustable
• Quickly Adapts to Most Floor Jacks with Removable Saddles
• Hang Bumpers, Store Glass, Many Other Uses
• Fits Jacks with Saddle Hole Dimensions of 1.17" - 1.19"(30mm)

An air hammer driven door skinning tool that is easily affordable.

• Skins doors in less than 10 minutes.
• Saves arm fatigue and time.
• Replaceable head skins at least 10 doors.

See the Skin Zipper video

• Compresses spring for easy, safe removal
• Sides safely enclose spring
• Heat-treated, high-carbon steel

Makes plug welding fast and easy!

Copper alloy backing plate revents burn thru (weld will not stick to the copper alloy). Plugweld Pliers allow you to turn up your heat for better penetration without burn thru, even if you have a pilot hole through the back panel.

The MIG Light allows you to light the area to be welded so that you can locate your torch where you need it before you strike an arc.

A large-diameter, easy push-on/push-off button can be actuated with your welding gloves on.

The MIG Light assists whether you are using a traditional or auto-darkening helmet.

Flexible mounting bracket attaches to the neck of standard (1/2" to 3/4") MIG welding torches.

The MIG's Light's focused beam saves time and frustration when welding out-of-position.

A great addition to your BigEasy kit, the BigEasy Night Light allows hands-free illumnation of the vehicle interior at night to allow tow driver, lock-out technician, officer and/or first repsonder to locate the door lock or keys while using the BigEasy Lock Out tool or other similar devices. Suction-cup design adheres the Night Light to the windshield or window of the vehicle. Powerful LEDs illuminate the interior so you know exactly where to position the BigEasy tool.

• Six powerful LEDs provide you the ability to focus a 1 foot diameter beam up to 4 feet away on the interior door lock area.
• Flexible 6-1/2 inch PVC suction cup design works in all temperature and weather conditions.
• Powered by three AAA batteries allows for one-person night-time lockout operation.

A Tool Holding Cover For Your Portable Bench!

• Easy, installs in seconds with hook & loop strips
• Folds flat for storage
• Holds tools and parts during assembly and disassembly

SAVE! When you buy our work stand combo!

• Hands free measuring
• Continuosly monitor your pull
• Measure without an assistant
• For Bodymen, Insurance Adjusters, Fabricators

Tough allow steel C-clamp locking pliers provide a quick temporary steering repair for vehicles with outer tie rod end ball and socket seperation.

• Saves tow driver's time by temporarily* fixing wheel alignment for easy loading and unloading.
• Allows mechanics to easily steer vehicle to repair bay.

*Tie Rod End Pliers' unique design with a socket end and pointed spindle end allow easy wheel pivoting for vehicle sterring by temporarily reconnecting ball and socket tie rod ends.

Temporarily secure a broken tie rod with this unique device.

Tie Rod Coupler eye-bolts secure the coupler to the broken tie rod by hand tightening or a small leverage bar.

• Saves tow driver's time by temporarily* fixing wheel alignment for easy loading and unloading.
• Allows mechanics to easily steer vehicle to repair bay.

*Do not use Tie Rod End Pliers or Tie Rod Coupler at speeds over 5 mph or distances over 100 yards.

A heavy-duty plastic tool that works like a chisel, but without the damage of hard metal.

• Tough plastic handle can be hit with a hammer
• Resharpen when needed with a file!
• Removes stick-on wheel weights from alloy wheels.
• Removes gaskets from aluminum parts.
• Removes decals, emblems and small moulding without scratching the paint.

One tool does it all!

A tough, duel-edged stainless steel scraper that can be sharpened.

For body technicians: Removes old paint, seam sealers from body panels, windshield sealer, moldings, weather striping, Urethane, and other tough adhesive items.

For mechanics: Removes stuck gaskets from engines and transmissions as well as separating engine components.