Extra-pigment ENGINE ENAMELS have been formulated by RestoMotive Laboratories to be the best and most beautiful engine enamels you can buy. Enamels are available in incredibly rich colors that flow easily, cover better than any other paint, and last longer. Por-15® enamels are non-flammable and conform to even the strictest California environmental standards. We invite you to compare them with any other product and you'll see what we mean. Typically, a pint is enough for an entire engine.

Note: Only Black and Chevy Orange are available in quarts.

BLACKCOTE™ is a permanent black coating developed for application over painted and unpainted surfaces. Apply over POR-15® Rust Preventive Paint for the toughest, most permanent protection against rust and corrosion ever developed.

BLACKCOTE™ is non-porous and will not crack, chip, or peel when properly applied according to directions. It has amazing scratch and abrasion resistance and is similar in strength to regular POR-15 Rust Preventive Coatings. BLACKCOTE™ is not sensitive to ultra-violet light and may be exposed to sunlight without damaging consequences. BLACKCOTE™ has excellent adhesion characteristics and may be applied over POR-15® Rust Preventive Paint months or years later with proper preparation.

CHASSISCOAT BLACK™ is a permanent black coating developed for application over painted and unpainted surfaces. Apply over POR-20® Rust Preventive Paint for the toughest, most permanent protection against rust and corrosion ever developed.

CHASSISCOAT BLACK™ is non-porous and will not crack, chip, or peel when properly applied according to directions. It has amazing scratch and abrasion resistance and is similar in strength to regular POR-15 Rust Preventive Coatings. CHASSISCOAT BLACK™ is not sensitive to ultra-violet light and may be exposed to sunlight without damaging consequences. CHASSISCOAT BLACK™ has excellent adhesion characteristics and may be applied over POR-20® Rust Preventive Paint months or years later with proper preparation.

STIRLING SILVER is a permanent silver coating developed for application over painted and unpainted surfaces. Apply over POR-20® Rust Preventive Paint for the toughest, most permanent protection against rust and corrosion ever developed.

STIRLING SILVER is non-porous and will not crack, chip, or peel when properly applied according to directions. It has amazing scratch and abrasion resistance and is similar in strength to regular POR-15 Rust Preventive Coatings. STIRLING SILVER is not sensitive to ultra-violet light and may be exposed to sunlight without damaging consequences. STIRLING SILVER has excellent adhesion characteristics and may be applied over POR-20® Rust Preventive Paint months or years later with proper preparation.

Is it bare metal, or is it METAL MASK™? Rejoice, restorers! After years of development, we have finally answered your urgent requests for a super-tough coating that looks just like bare metal. Now you can permanently coat and protect all of those components on your chassis that were left unpainted by the factory when the vehicle was new. Items such as spindles, steering boxes, coil brackets, rear ends, leaf springs, bolt heads, suspension components, master cylinders, coil springs, gas tanks, cast iron transmission housings, and others will look 'factory correct' when coated with METAL MASK™.Gone forever are the days when you had to rely on cheapo cans of enamel spray paint that look good for a few months or weeks, but cannot withstand the rigors of the road.

METAL MASK™ is extremely tough, very chip and scratch resistant, and amazingly close to the color of brand-new cast iron or bare steel.

And, METAL MASK™ is the perfect coating for the high stress bracketry, such as hood hinges, hood springs, hood latch assemblies, etc. It is super tough yet flexible, making it perfect for those areas where enamel paint is sure to flake away.

Try METAL MASK™ on your project today!

HARDNOSE™ Paints are tough, glossy, two-component coatings for use over primed or painted surfaces. They are moisture cured, so exposure to moisture and humidity will actually improve their performance and strength.

When fully cured, HARDNOSE™ Paint is rock-hard, chemical resistant, non-porous, and incredibly tough. Durable and easily cleaned, they will not crack, chip, peel, or fade with age. HARDNOSE™ Paint will withstand even the most intensive UV environments.

These beautiful, two-component coatings are stronger than any color paints you have ever tried. The long-lasting brilliant colors will look terrific wherever you use them, and will withstand incredible abuse. You'll be amazed and delighted at how well HARDNOSE™ Paint holds up under conditions that would quickly destroy ordinary finishes.

HARDNOSE™ Paint is also excellent for industrial applications. Use our safety yellow or orange colors on machinery guards or heavy equipment, and then stand back and marvel at how long they last under abuse.

Put HARDNOSE™ Paint on the chassis of your car, truck, or motorcycle, and quit worrying about stone chips and gravel roads. You'll be amazed at the toughness!

WARNING: THIS PRODUCT CONTAINS ETHYLBENZENE - A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.

BLACK VELVET is the only black paint capable of withstanding extreme temperatures up to 1200F. This high temp paint will maintain a rich black color and won't burn off. Can be used on all cars, domestic or foreign, and it meets or exceeds properties and requirements of MIL-C-13370. Can be brushed or sprayed.

For years we've been working on a product to repair cracks, pits or holes in exhaust manifolds, tailpipes, mufflers, or other components subjected to high temperatures while in use. Because replacement parts are often difficult or impossible to find, there is a real need for this type of product in the marketplace. FIRE SEAL 2000™ is a single-component (no mixing required) ceramic and stainless steel-filled putty that is resistant to fuels, oils, and corrosives. After it is fully cured, it will withstand temperatures up to 2000° F. FIRE SEAL 2000™ may be applied to rough-surfaced or sandblasted steel, stainless steel, or cast iron.

Instructions: Use a putty knife, small trowel or spatula to apply. Curing: Let FIRE SEAL 2000™ dry for 16-24 hours. Begin final cure by idling engine for 10-15 minutes at a time. You may sand FIRE SEAL 2000™ after it is fully cured, using a file or medium grit sandpaper. Do not use any lubricants for machining, but always use a dust mask to avoid inhaling the sanding dust.

FACTORY MANIFOLD GRAY is a high temp gray paint capable of withstanding extreme temperatures up to 1400F. This high temp paint will maintain a durable iron gray color and won't burn off. Can be used on all cars, domestic or foreign, and it meets or exceeds properties and requirements of MIL-C-13370.

This Aluminum high temperature paint is capable of withstanding temperatures up to 1400 F, POR-20® is also extremely weather, salt and moisture resistant. Helps prevent cracking, chipping, and peeling.

You will be excited by its performance and beauty. We guarantee this to be the most brilliant, uniform heat resistant coating available anywhere.

Can be brushed or sprayed.

A Brilliant Two-Component Clear Coating

GLISTEN PC™ is a High Gloss, Rock Hard, Water-clear topcoat designed for spray or brush application over all metal surfaces, including highly polished aluminum and chrome surfaces. GLISTEN PC™ will not leave brushmarks, and will dry in less than one hour, but will take 3-4 days to reach maximum hardness.

When GLISTEN PC™ is first dry to the touch, it will appear to be very soft. Avoid touching it for several days until it becomes hard and tough. Accidental contact could damage the surface before full cure has taken place. Like many other coatings, GLISTEN PC™ is a MOISTURE-CURED coating, which means it is strengthened by exposure to moisture. It will never crack, chip, peel, or yellow, and is very flexible as well.

Note: When applying over polished metals (aluminum, chrome, brass, copper etc) you must use AP120 metal prep according to instructions.

IDEAL USES: As a protective coating on aluminum wheels, chrome bumpers, marine railings, chrome or aluminum covers, grills, handles, ornaments, lights, etc.

WARNING: THIS PRODUCT CONTAINS ETHYLBENZENE - A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.

In response to many customer inquiries requesting a quick drying and easy-to-apply coating which enables a restorer to quickly topcoat POR-15® and other basecoats, we have developed POR-15® Self-Etching Primer.

With this product, you can even topcoat POR-15® that's been in place for months or years.

POR-15® Self-Etching Primer is NOT a high-build primer, like POR-15®'s TIECOAT PRIMER, but it can be sprayed or brushed on almost any painted surface and can be topcoated in 15 - 30 minutes. It bonds incredibly well to POR-15® Rust Preventive Paint, and all topcoats bond incredibly well to POR-15® Self-Etching Primer. It can be sanded lightly, and, if desired, multiple coats may be applied.

We strongly recommend this fine product, which we sell with our unconditional money-back guarantee of satisfaction. It is available in pints, quarts, and gallons as well as a large aerosol spray (15 ounces). In situations where you are topcoating a very old POR-15® finish, we first recommend a light sanding with any 280 to 320 grit paper.

Now you can prime and paint right over cured POR-15 with our new TIE-COAT PRIMER. We developed this special "interlocking" primer after many requests from customers who wanted a coating with special adhesion characteristics that make it perfect for most painted surfaces, especially POR-15.

TIE-COAT PRIMER is highly resistant to penetrating topcoats, like lacquers, enamels, and two-component finishes. It sands very smoothly, as well. Try some on your next project.